DEVICE OVERVIEW The PIC16F707/PIC16LF707 devices are covered by this data sheet. They are available in 40/44-pin packages. Figure 1-1 shows a block diagram of the PIC16F707/PIC16LF707 devices. Table 1-1 shows the pinout descriptions. High-Performance RISC CPU: • Only 35 Single-Word Instructions to Learn: - All single-cycle instructions except branches • Operating Speed: - DC – 20 MHz clock input - DC – 200 ns instruction cycle • 8K x 14 Words of Flash Program Memory • 363 Bytes of Data Memory (SRAM) • Interrupt Capability • 8-Level Deep Hardware Stack • Direct, Indirect and Relative Addressing modes • Processor Read Access to Program Memory • Pinout Compatible to other 40-pin PIC16CXXX and PIC16FXXX Microcontrollers Special Microcontroller Features: • Precision Internal Oscillator: - 16 MHz or 500 kHz operation - Factory calibrated to ±1%, typical - Software selectable ÷1, ÷2, ÷4 or ÷8 divider • 31 kHz Low-Power Internal Oscillator • External Oscillator Block with: - 3 crystal/resonator modes up to 20 MHz - 3 external clock modes up to 20 MHz • Power-on Reset (POR) • Power-up Timer (PWRT) • Oscillator Start-Up Timer (OST) • Brown-out Reset (BOR): - Selectable between two trip points - Disabled in Sleep option • Watchdog Timer (WDT) • Programmable Code Protection • In-Circuit Serial Programming™ (ICSP™) via two pins • In-Circuit Debug (ICD) via Two Pins • Multiplexed Master Clear with Pull-up/Input Pin • Industrial and Extended Temperature Range • High-Endurance Flash Cell: - 1,000 Write Flash Endurance (typical) - Flash Retention: >40 years - Power-Saving Sleep mode • Operating Voltage Range: - 1.8V to 3.6V (PIC16LF707) • 1.8V to 5.5V (PIC16F707) Extreme Low-Power Management PIC16LF707 with nanoWatt XLP: • Sleep mode: 20 nA @ 1.8V, typical • Watchdog Timer: 500 nA @ 1.8V, typical • Timer1 Oscillator: 600 nA @ 1.8V, typical @ 32 kHz mTouch™ Technology Features: • Up to 32 Channels • Two Capacitive Sensing modules: - Acquire 2 samples simultaneously • Multiple Power modes: - Operation during Sleep - Proximity sensing with ultra low µA current • Adjustable Waveform Min. and Max. for Optimal Noise Performance • 1.8V to 5.5V Operation (3.6V max. for PIC16LF707) Analog Features: • A/D Converter: - 8-bit resolution and up to 14 channels - Conversion available during Sleep - Selectable 1.024V/2.048V/4.096V voltage reference • On-chip 3.2V Regulator (PIC16F707 device only) Peripheral Highlights: • Up to 35 I/O Pins and 1 Input-only Pin: - High current source/sink for direct LED drive - Interrupt-on-pin change - Individually programmable weak pull-ups • Timer0/A/B: 8-Bit Timer/Counter with 8-Bit Prescaler • Enhanced Timer1/3: - Dedicated low-power 32 kHz oscillator driver - 16-bit timer/counter with prescaler - External Gate Input mode with toggle and single shot modes - Interrupt-on-gate completion • Timer2: 8-Bit Timer/Counter with 8-Bit Period Register, Prescaler and Postscaler • Two Capture, Compare, PWM modules (CCP): - 16-bit Capture, max. resolution 12.5 ns - 16-bit Compare, max. resolution 200 ns - 10-bit PWM, max. frequency 20 kHz • Addressable Universal Synchronous Asynchronous Receiver Transmitter (AUSART)