AT45DB321E-SHF-B Memory: CAD Models, Datasheet, Features [Video&FAQ]

Catalog

Product Overview

The Adesto AT45DB321E is a 2.3V minimum, serial-interface sequential access Flash memory ideally suited for a wide variety of digital voice, image, program code, and data storage applications. The AT45DB321E also supports the RapidS serial interface for applications requiring very high speed operation. Its 34,603,008 bits of memory are organized as 8,192 pages of 512 bytes or 528 bytes each. In addition to the main memory, the AT45DB321E also contains two SRAM buffers of 512/528 bytes each. The buffers allow receiving of data while a page in the main memory is being reprogrammed. Interleaving between both buffers can dramatically increase a system's ability to write a continuous data stream. In addition, the SRAM buffers can be used as additional system scratch pad memory, and E2PROM emulation (bit or byte alterability) can be easily handled with a self-contained three step read-modify-write operation.

Unlike conventional Flash memories that are accessed randomly with multiple address lines and a parallel interface, the Adesto DataFlash uses a serial interface to sequentially access its data. The simple sequential access dramatically reduces active pin count, facilitates simplified hardware layout, increases system relibility, minimizes switching noise, and reduces package size. The device is optimized for use in many commercial and industrial applications where high-density, low-pin count, low-voltage, and low-power are essential.

To allow for simple in-system re- programmability, the AT45DB321E does not require high input voltages for programming. The device operates from a single 2.3V to 3.6V power supply for the erase and program and read operations. The AT45DB321E is enabled through the Chip Select pin (CS) and accessed via a 3-wire interface consisting of the Serial Input (SI), Serial Output (SO), and the Serial Clock (SCK).

All programming and erase cycles are self-timned.

AT45DB321E-SHF-B Related Video Introduction

Video Description: High speed programmers to program serial flash (SPI) memory. Support in system programming and off line programming.

AT45DB321E-SHF-B CAD Models

Figure: AT45DB321E-SHF-B PCB Symbol

Figure: AT45DB321E-SHF-B Footprint

Figure: AT45DB321E-SHF-B 3D Models

AT45DB321E-SHF-B Pin Configuration

Figure: AT45DB321E-SHF-B Pin Configuration

AT45DB321E-SHF-B Block Diagram

Figure: AT45DB321E-SHF-B Block Diagram

AT45DB321E-SHF-B Features

• Single 2.3V - 3.6V supply
• Serial Peripheral Interface (SPI) compatible
• Supports SPI modes 0 and 3
• Supports RapidS" operation
• Continuous read capability through entire array
• Up to 85MHz
• Low-power read option up to 15MHz
• Clock-to-output time (tv) of 6ns maximum
• User configurable page size
• 512 bytes per page
• 528 bytes per page (default)
• Page size can be factory pre-configured for 512 bytes
• Two fully independent SRAM data buffers (512/528 bytes)
• Flexible programming options
• Byte/Page Program (1 to 512/528 bytes) directly into mainmemory
• Buffer Write
• Buffer to Main Memory Page ProgramFlexible erase options
• Page Erase (512/528 bytes)
• Block Erase (4 KB)Sector Erase (64 KB)
• Chip Erase (32 Mbits)
• Program and Erase Suspend/Resume
• Advanced hardware and software data protection features
• Individual sector protection
• Individual sector lock down to make any sector permanentlyread-only
• 128-byte, One-Time Programmable (OTP) Security Register
• 64 bytes factory programmed with a unique identifier
• 64 bytes user programmable
• Hardware and software controlled reset options
• JEDEC Standard Manufacturer and Device ID ReadLow-power dissipation
• 400nA Ultra-Deep Power-Down current (typical)
• 3μA Deep Power-Down current (typical)25μA Standby current (typical)
• 7mA Active Read current (typical)
• Endurance: 100,000 program/erase cycles per page minimum
• Data retention: 20 yearsGreen (Pb/alde-freeRoHS compliant) packaging options
• 8-lead SOIC (0.208" wide)
• 8-pad Ultra-thin DFN (5 x6 x 0.6mm)
• Die in Wafer Form

AT45DB321E-SHF-B Datasheet

You can download the datasheet from the link given below:

AT45DB321E-SHF-B Datasheet

AT45DB321E-SHF-B Specifications

AT45DB321E-SHF-B Manufacturer

Adesto is a leading provider of low power Flash memory, application-specific semiconductors and embedded systems that comprise the essential building blocks of IoT edge devices operating on networks worldwide. Their broad portfolio of non-volatile memory, Analog and digital IP, IoT edge servers, routers, network nodes and communication modules are designed to improve the efficiency and lower the cost of equipment applications in consumer, industrial, communications and medical applications.

Using Warning

Note: Please check their parameters and pin configuration before replacing them in your circuit.

AT45DB321E-SHF-B FAQ

What is a serial flash memory?

A serial Flash device is a non-volatile memory that can be electrically erased and reprogrammed. It is used for storing executable code in devices such as DVD players, DSL modems, routers, hard-disk drives, and printers.

How does SPI Flash work?

The SPI flash is connected to an SPI unit of the CPU via CLK, MOSI, MISO, nCS pins. This is the minimum connection needed to store data on the SPI flash and get data from it. This connection actually works with any CPU that provides an SPI unit.

Is SPI Flash NAND or NOR?

SPI flash media, both NAND and NOR, requires only eight traces to the processor - an equivalent parallel solution can require twenty-three. In addition to reducing the number of traces, these devices take up considerably less space on the PCB.